An Easy Tutorial for Bathtub Installation
An Easy Tutorial for Bathtub Installation
Blog Article
What're your thoughts about How to Install a Bathtub?
Installing a bathtub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a new one is likewise a moderately challenging task. If the old tub is conveniently accessible, the task can relocate quickly; if you need to open a wall surface to remove the old bathtub and also place the new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Make certain you have actually certified yourself for the job as well as fit trying it. Instead of working with a contractor to take control of a halfway-completed job, it is better to take into consideration using one before you start. Possibilities are you might require an expert plumber to make tube connections.
This post will certainly aid you mount a new tub in your shower room if you have actually already acquired a new tub and do not need to alter the setup of your previous water pipes.
Your tools as well as material checklist need to comprise the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the tub in the needed placement. The wood boards are handy in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by checking the level as well as changing the feet on the tub up until the spirit level checks out level.
To mount taps, fit the bottom of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the water system and examine all joints and brand-new pipework for leaks and also tighten them if required. Load the bath tub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bath tub needs to wait up until the bath tub has been used a minimum of once as this will certainly settle it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about issues with moisture and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to always fill the tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealer can split rather very early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that excerpt was really useful. Be sure to take a moment to share this article if you enjoyed it. Thank-you for your time spent reading it.
Top-notch service? Dial here. Report this page